sprucecougar60

How to Replace a Kia Sportage Replacement Key For many Kia models, the key contains a built-in keyless entry system. The key functions like remote controls and can be exchanged by an Kia dealer. Key fobs can stop working for a variety of reasons, such as an empty coin battery worn buttons, signal interference, water damage and a faulty receiver module. Here are some tips to assist you in getting your Kia sportage replacement key to work for good. How to replace a remote key or a smartkey? No matter if your Kia is equipped with an intelligent key, remote key, push to start key, or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is particularly when your car displays a message telling you that the smart or remote keys have low battery power. It's a simple procedure. To replace the battery on the keyfob remove the mechanical key from the slit on the back of the fob. Then, you need to pry the cover off. A small screw is inside the key fob that holds the battery in its place. By using a small screwdriver take the screw off and pull out the battery that was in place. Install the new battery and then close the cut on the key fob. Test the key fob by pressing the lock/unlock buttons. If kia replacement keys G28 Car Keys Solutions and unlock in the same way, you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or when you need to go on errands around Brandon. Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a particular programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your key has to be programmed, you must know the key code number that is stamped on the tag that identifies the key and save it in a secure location. How to replace the battery If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A low battery could cause other issues, such as the check engine light turning on or delayed cranking of the engine. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires just the most basic tools. Before starting the process be sure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the key comes out. This key can be inserted into the driver door handle to unlock your car. To replace the battery in the key fob, take off the cover on the rear. Use a plastic pry tool to open the latch that holds the black negative cable. Take the old battery out, and then place the new battery to ensure its “+” side faces you and the “–” negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts. After the new battery has been installed after which you turn the key fob off and then turn it on in the ignition for a few times until the door locks. You can then test the Kia's key fob again to make sure it's functioning properly. How to replace the smart key? Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key features an embedded mechanical key blade, while the standard key fob does not. Both key fobs contain batteries that will eventually require changing. This is a straightforward process which takes just two minutes. Before you get started before you begin, ensure that you're on a flat surface with adequate lighting and that the Kia is off. Keep in mind that the fob has small parts that can be thrown off should you not be careful. The first step is to locate the small release button that is located on the backside of the fob. It will be a circular button or rectangular slot. When you press it the mechanical key blade will be released and you can then open the key fob. After the key fob has been opened, remove the battery. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. Once you're done you should be able to lock or unlock your car with your key fob, even if the engine isn't running! How to replace the mechanical key? The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car with just pressing a button. But like any device it will encounter issues from time to time. There are solutions to fix these problems and keep your key fobs in good working order for the duration of. One of the most frequent issues is a low or dead battery. This can cause the fob to stop working completely or work intermittently. If this is the case then replace the battery with a new one. If this does not resolve the issue, you can use the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed, replace it with a new one. Once the new battery is installed, close and unlock the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can fit into the slot). Test the key fob to verify that it's functioning properly. If the device isn't working, contact an authorized locksmith or dealer to resolve the issue. Make sure they cut you an emergency key that functions across all trunk and door cylinders in order to avoid lockouts in the future.